New TyreON TSC5000X2A Alignment scissor lift - On floor - Free wheel liftin scissor car lift

Capacity 5000 kg - On floor
Liftheight 216 cm
Runway LxW 530 cm x 60 cm
Drive motor 3,5 kW (C16A)
2nd scissor 4T - H43cm - L150 -- 200 cm
► LED8P runway lighting
► Rails for optional rolling jack
► 1.3 meter ramps
► Hose sets + floor covers
Onfloor height 31 cm
Foundation C20/25 - 600 x 300 x 20 cm
Lifting/Lowering About 70 s
Inground-version Available
Voltage 400V
Colour Anthracite gray / light gray
Hydraulic oil is not included 18 L TyreON HV-ISO-32 is optional
Alignment lift with wheel-free lifting system in the runways.
The control panel comes with a display showing the status of various functions.
Most robust and reliable 5T scissor lift available on the market.
Super-balanced construction for wheel alignment and 1 meter space between the 5.3 m long runways.
Large working range - from very short to very long wheelbase
Integrated LED lights along the length of runways
Wheel-free lifting system with extendable lifting platforms
Heavy duty hydraulic pump with load-sensing lowering valve
Multifunctional: for inspection, maintenance, repair, wheel alignment, testing of headlights and driver assistance systems, etc.
TyreON OFK1 on floor kit with 130,5 cm ramps, floorcovers and cutters is included
TyreON TSC5000X2A Alignment scissor car lift - On Floor installation
Suitable for short and long passenger cars (multiple stretch extra large) vans and small lorries
Easy access - Easy access - the 64 cm wide ramps with anti-slip profile are 130,5 cm long
With long scissors and oversized runways
Two hydraulic cylinders for heavy lifting
Manual override for descending in case of power outage (handpump)
Safety valve (overload safety) - No damage to car lift in case of overload
Remote controlled lift of about 2,6 meter or less
Fully powder coated finish
Required air pressure 8 - 10 bar
Simple installation with system integrated depressurization and runway leveling out procedure
ControllerL x B x H (cm)35,5 x 37 x 108
Free Wheel system and wheel alignment
With the extra long rear wheel plates and spacious recesses for turntables, the TSC5000X2A is suitable for aligning short and long chassis vehicles up to 5T.
Regular and 3D wheel alignment
Hydraulic free wheel system -4000 kg - height 43 cm
Extendable tables 150 - 200 cm.
Runways with cut-outs for turntables - shims included
Runways with built-in movable rear wheel plates - mechanically lockable
XL rear wheel plates - 1.8 meter
Safety features - CE-Stop
Voltage through entire lift and control panel is only 24V
Automatic and accurate syncing function of the runways
CE-Stop: end height switch at 30 cm, additional manual input required for final stage of descending
Lowered descending velocity during final stage and acoustic and optical signal
Hydraulic shut-off valve and hose failure safety system
Automatic safety lockup - 19 lock positions
Automatic unlocking of safety safety system (air)
Built-in sensor shuts down engine at maximal level
Roll-off protected runways
With Bonus features as standard 
Large working range, high performance
5T capacity - 5.3 meter runways
216 cm Lifting height
Long rear wheel alignment plates and various positions for front wheel turn plates
Free wheel system with extendable platforms including 4 rubber lifting blocks
Complete, equipped with
LED8P runway lighting LED 24V including grilles for protection
Rails for TRJ25A axle jack 2.5T (optional)
Installation material included
Hydraulic tube set
Air tube set
Floor covers
Groundanchors
CE-certification
Scissor inground installation alignment car lift
• EN1493:2010 Vehicle Lifts
• EN 60204-1:2006+AC:2010 Safety of machinery - Electrical equipment of machines - Part1: General requirements
• EN ISO 12100:2010 Safety ofmachinery – general principles for design – Risk assessment and risk reduction
-
TSC5000X2A Alignment scissor lift - On floor - Free wheel lifting system - 5.3 m lightened runways - 5T- Mounted on the floor
The price is excluding VAT and delivery costs.